Wednesday, May 20, 2009

Messing With a Crosman Model 70, Part 2

On I go.

Those two screws hold the plate covering the trigger group.

The trigger group.

Not much to keep track of.

A roll pin holds a plastic plug that retains the hammer assembly.

Most of the hammer parts...

The bolt just slips out once the hammer and sleeve are removed.

Wait, there's more! Another spring keeps the hammer off of the valve stem and regulates the striking force.

There was a bit of corrosion on the pot metal receiver.

Just a pic to remind the right way for the safety to be installed...

Once cleaned, I started to put it back together. It's important to align the hammer sleeve.

The trigger assembly goes back together in reverse. I lubed all the trigger components.

You can see the old piercing pin on the right was a bit mashed up.

The cam was binding on the tapered nut. I think this is because of the redesign of the piercing pin and seal for the 38 - the new seal is thicker?

You can see a line across the cam surface where it catches on sharp edge of the nut.

So I made a slight radius on the nut edge.

The screw hole holding the barrel down in front was stripped, so I drilled it out and tapped it 8-32.

After assembly I found the barrel was a bit low (as evidenced by being out of the adjustment range on the scope crosshairs), so I added a washer between the stock and the barrel boss shown above.

Once a few sighting shots (the non-grouped holes) were taken, you can see I got an ok group.

I found the trigger pull was insanely heavy. So I polished all the surfaces.

And swapped a lighter spring for the old one.

Doesn't look too bad!

I scoped it because the rear sight is broken, which will be covered next installment.

Tuesday, May 19, 2009

Messing With a Crosman Model 70, Part 1

I placed a "WTB Beaters" ad on the yellow forum last month and was able to buy several abused airguns on my want list. One of these was a Crosman Model 70 Rifle.

As received there was clearly a problem with the CO2 cartridge loading port.

The steel strap was bent.

I unscrewed the strap.

Pretty severe.

Tweaked.

So I hammered and bent.

This method worked the best.

But I then had to shrink and stretch the metal through selective hammering to get it flat again...

Not bad.

Still a little bent though. More hammering and tweaking...

Finally about as good as it'll get.

You can see the cam mechanism, that bears on the tapered nut for piercing the cartridge.

That screw adjusts the tension.

One setscrew removes the barrel and shroud.

The shroud is solid(?) and I'm assuming molded in place around the barrel.

The piercing pin and seal is the same as used on the Crosman 38 revolvers.

Unscrewing the valve.

The inlet and exhaust valve parts removed.

Saturday, May 16, 2009

Making a Steel Breech for a Crosman 2240, Part 3

Almost done...

About to mill the slot for the bolt handle.

And milled.

This is a rather convoluted setup for milling the bolt catch. The breech is tilted on its side 30 degrees.

The slot cut.

A Crosman bolt (from their steel breech) fits perfectly.

Again, the rough finish.

Assembled on the 2240 to check for fit and function.

Now to do something about the finish.

An aluminum rod was turned up to be 7/8" diameter minus the thickness of some sandpaper. I used it to sand the radius smooth.

Looks much better.

I was going to lap the sides against sandpaper but then I remembered that I had a surface grinder! So I started to grind the sides.

I probably removed about 2-3 thousandths on each side.

Grinding the chamfer on the bottom.

Shiny, now I regret not making it from stainless...

A 220 grit Scotch-Brite Bristle Disc on my polisher.

I deburred and smoothed. You can see some sandpaper wrapped around a file just above the breech. I used it to smooth the breech cutout and the dovetail surfaces. I still see some faint milling marks but I'll live with those.

Another view. I tapped the two holes for the barrel setscrews.

I turned up an end plug.

And made a decorative series of grooves in the face.

I blued both with Oxpho Blue. I'm going to see if I can get it darker.

You can see reflections in the breech. Now I need to work on the bolt and bolt handle as well as figuring out what length barrel to use. But not bad for a first breech?